Ultrasonic principles; properties of sound; waves, frequencies, sound beam, attenuation; gauges for measuring thicknesses and flaw, ultrasonic compression probes; calibration blocks, methods of calibration, sensitivity and sizing techniques, testing of plates, lamination and thickness, etc. Ultrasonic Testing: Contents: Training & Certification, The following are some of the training contents with regards to Ultrasonic Testing:
The content of the training course on Ultrasonic Testing (Level 2) would consist of the following:-
- Principles of Ultrasonic Testing
- Generation of Ultrasonic Testing
- Properties of the transducer or probes
- Acoustic impedance, Beam Divergence
– Dead, Near and Far Zone
- Influence of properties of test object on sound propagation
- Sound velocity and attenuation - Equipment
– controls and functions of ultrasonic instrument
- Signal presentation – A,B,C and D scans
- Scanning techniques – manual, semi-automatic, automatic
- Immersion testing and Through-transmission technique – basic principles
- Calibration of Testing Systems
- Sensitivity setting – simple methods, BWE, DAC
- Detectability of Defects – advantages and limitations of the test method with regard to defect detection
- Factors Affecting the Performance of the Ultrasonic Test
- Conducting and Recording the Test
- Procedure to be adopted to carry out the test and flaw assessment, sizing techniques and reporting
- Snell’s Law concerning reflection, refraction, mode conversion and calculations
- Interpretation of test Results to acceptance standards
- Basic Welding Process and product technologies
- Types of defect associated with particular parent metal/welding process combinations
- Examination of parent plate, butt welds and configuration joints
Training Hours: 120 hours
The content of the training course on Ultrasonic Testing (Level 1) would consist of the following:-
- Principles of Ultrasonic Testing
- Generation of Ultrasonic Testing
- Properties of the transducer or probes
- Beam Divergence – Dead, Near and Far Zone
- Influence of properties of test object on sound propagation
- Sound velocity and attenuation
- Equipment – controls and functions of ultrasonic instrument
- Signal presentation – A,B and C scans
- Scanning techniques – manual, semi-automatic, automatic
- Immersion testing and Through-transmission technique – basic principles
- Calibration of Testing Systems
- Sensitivity setting – simple methods, BWE
- Detectability of Defects – advantages and limitations of the test method with regard to defect detection
- Factors Affecting the Performance of the Ultrasonic Test
- Conducting and Recording the Test
- Procedure to be adopted to carry out the test and flaw assessment, sizing techniques and reporting
- Snell’s Law concerning reflection, refraction, mode conversion and calculations
- Interpretation of test Results to acceptance standards
- Basic Welding Process and product technologies
- Types of defect associated with particular parent metal/welding process combinations
- Examination of parent plate, butt welds and configuration joints
Training Hours: 80 hours
At the end of the course, attendees shall be able to:
- Select suitable NDT technique and test method to be used
- Define the limitations of application of the testing method
- Translate NDT standards and specifications into NDT
- Measure thickness of steel plates & determine levels of attenuation
- Conduct test as per specifications
- Interpret and evaluate results according to applicable standards
- Organise and report the results of non-destructive tests
- Meets syllabus requirements for PCN or ISO9712 examinations
Time Table Of Course (Level 2) :
Day 1 to Day 5
- Introduction of NDT
- Theory - General,Specific and Product Technology
- Course work
Day 6 - Day 15
- Understanding about Instrument
- Calibration
- Construct Beam Profile
- Construct D.A.C
- Plotting System
- Scanning Technique
- Scanning (Lamination,Plate,Pipe,Nozzle and Node)
- Detection any Inclusion or Lamination
- Reporting
Time Table Of Course (Level 1) :
Day 1 to Day 5
- Introduction of NDT
- Theory - General, Specific and Product Technology
- Course work
Day 6 - Day 10
- Awareness training on understanding about the instruments
- Calibration
- Construct Beam Profile
- Plotting System
- Scanning Technique
- Scanning (Thickness Measurement, Lamination & Plate.)
- Detection of any Inclusion or Lamination
- Reporting
*All Fees are subjected to 8% SST
| 5th May - 26th May 2025 |
| 9th June - 30th June 2025 |
| 7th July - 25th July 2025 |
| 4th August - 22ng August 2025 |
| 8th September - 29th September 2025 |
| 6th October - 27th October 2025 |
| 3rd November - 21st November 2025 |
| 1st December - 19th December 2025 |
* Training dates may be postponed or cancelled without prior notice unless we have confirmed your slot.
No.18, Jalan Tanjung SD13/2,
Bandar Sri Damansara,
52200 Kuala Lumpur,
Malaysia
Mondays to Fridays
9.00am - 5.30pm
Saturdays, Sundays and Public Holidays
Closed
E-mail info@mindt.com.my
Note: Please add our email info@mindt.com.my to your address book to avoid our email going to your spam folder.
TELEPHONE +603 6280 3448
MOBILE +6011 6518 0600